8/28/2023 0 Comments Zbra stockChicago Mercantile Association: Certain market data is the property of Chicago Mercantile Exchange Inc. Factset: FactSet Research Systems Inc.2019. Market indices are shown in real time, except for the DJIA, which is delayed by two minutes. In order to obtain the print file, you'll go to the "File > Print" dialog in BarTender, enable the "Print to File" checkbox and now click on "Print".Most stock quote data provided by BATS. If the problem persists, please send me your new BarTender document (.btw), a scan of how the labels print and as well a print file which demonstrates the issue. Make the page setup adjustments as mentioned to you, then print. It would be fine if you could create a new BarTender document (.btw) and just place some Sample Text on it (one text object using Windows fonts, the other text object using printer internal fonts). You can then always make position adjustments by modifying the gap height and gap offset and by doing position adjustments (you do this via the "File > Print > Document Properties." dialog, but you mention you've already tried this. I will have to get some pictures to demonstrate.Ĭould you send me the corrected BarTender document for me to examine, where the top and bottom margins are set to 0 and where the page height equals the physical label height (without counting the gap). It is as if the printer driver is incorrectly reading the Origin point of the label. When I print to my ZPL printers with the 7.3.3 drivers there is an unprintable region that no amount of tweaking will get the image into. 16 years (and being a Journeyman in the trade) of profiling various printers and stocks would lead me to not question my page set-ups, I will however contend that you would have seen those margin settings as odd possibly. This is a variance issue as a result of shadows on the sensor caused by the thickness of the stock. 03" at the top to represent uprintable regions. If the sensor reads your stock height as 2.03" you set page height to 2.03" and the template with a margin of. To properly set a page set-up the stock needs to be set to the height and width of the stock as determined by the sensor on the printer then you set your page template to match the correct size of the stock. That little bit of margin at the top and extra added to the side to side was from trying to move the image around. If this appears incorrect to you as well, please correct the problem.Īlso, under the "File > Print" dialog and now the "Object Print Method" tab, try setting the lines an boxes to print as Raster Graphics instead. Is that really how you've setup your page setup? In "labels with gaps" stock, the top and bottom margins need to be set to 0 and the page height needs to equal the label height (in a 1 row based page), which physically corresponds to the height of the label without counting the label gap. When opening this BT document I see that under the "File > Page Setup", now under the "Page" tab you've set a "Page Width" of "2.106" inches and under the "Layout" tab you've set a "Top" margin of "0.03" inches. Thanks in advance if you need any additional information I am ready to supply it. None of my other Zebra printers have this issue. All of my stocks are portrait and 0 degrees. I have toyed with the Gap Offset and the advanced options for Position Adjustment. This is particularly an aggravation when I have to print on 0.375" x 0.375" label stocks. No matter what adjustments I make I cannot make the printers print inside this area. In Bartender I have the page setup for the same values. Gap Height: 0.12 Gap Offset: 0.0 (adjusting this just makes them go higher up the label, it won't accept a negative value) Under the printing preferences -> Page Setup -> Stock I set up a New stock with My GC420t printer gives me q408 Q102,24 which equates to a 2" W 0.5"H and 0.12" Gap reading. Then I take the calibrated values from the printers to use for setting up the stock information. I set up my printers and follow the calibration techniques for the printers. Using non-continous gapped labels 0.08" from the left margin and bottom margin are unprintable areas.īarTender Enterprise Automation version 10.0 I have 3 different Zebra EPL printers that all have the same oddity when printing from Bartender.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |